These maintenance steps will prevent most refrigerator breakdowns.
FamilyHandyman.com | Sep 12, 2024
These maintenance steps will prevent most refrigerator breakdowns.
Cleaning the condensor coils is a very common refrigerator repair. Condenser coils are located on the back of the fridge or across the bottom. These coils cool and condense the refrigerant. When the coils are clogged with dirt and dust, they can’t efficiently release heat. The result is your compressor works harder and longer than it was designed to, using more energy and shortening the life of your fridge.
Clean the coils with a coil cleaning brush and vacuum. A coil cleaning brush does a thorough job and will easily pay for itself. The refrigerator coil brush is bendable to fit in tight areas. They can be used for cleaning your dehumidifier and air conditioner coils too.
You can eliminate more than 70 percent of refrigerator repair and service calls with this simple cleaning step.Do it twice a year or more often if you have shedding pets. Their fur clogs up the coils fast.
Unsnap the grille at the bottom of the refrigerator to access the coils. If your coils are located on the back, you’ll have to roll the fridge out to get at them.
Clean the coils with a special refrigerator coil cleaning brush to loosen the dirt and dust. Vacuum the coils as you brush. Be careful not to bend the fan blades. A gentle brushing will do the job.
Some refrigerators have the coils on the back of the unit. Brush and vacuum these coils in the same manner as coils found under a refrigerator.
Always unplug your fridge before working on it!
If the coils are located on the bottom of the fridge like ours, clean the condenser fan and the area around it. Fridges with coils on the back don’t have a fan. The fan circulates air across the coils to help cool them. At times, paper, dirt, dust and even mice can get sucked into the fan and bring it to a complete stop.
Yours could be in a different area, but it’s always next to the compressor. Most refrigerators will have a diagram on the back or folded up under the front grille showing the location of the major parts. While you’re under there, wipe out the drip pan, a flat pan that collects water from the defrost cycle and allows it to evaporate.
Access the condenser fan by rolling the fridge away from the wall and removing the lower back cover with a screwdriver. Replace the cover when you’re finished. It’s essential for good air circulation.
Clean the fan blades with the brush and vacuum so air can move freely across them. Also clean the shaft by vacuuming the crease where the blade meets the motor. Don’t lubricate the shaft; oil will attract dirt and cause problems.
Prevent an expensive refrigerator gasket repair bill and cut down air leaks by keeping your door gasket clean. Syrup, jelly or any other sticky stuff dripping down the front sides of your refrigerator can dry and glue the gasket to the frame. The next time you open the door, your gasket can tear. Keep it clean and you’ll get a nice, tight seal, keeping the cool air where it belongs, in the fridge.
To prevent wear, lubricate the door handle side of the gasket by sprinkling baby powder on a cloth and wiping it down once a month.
Wipe the door gasket regularly with warm water and a sponge. Don’t use detergent—it can damage the gasket.
These little vents on frost-free fridges allow air to circulate in the freezer. Don’t block them or let crumbs or twist ties get sucked in around the evaporator fan or clog the drain tube. To help save energy, keep your freezer about three-quarters full to retain cold air. But don’t pack it any fuller because the air needs to circulate.
Clear food packages away from the vent openings and clean the air return so crumbs and twist ties don’t clog them.
This step won’t necessarily prevent a refrigerator repair, but it’ll extend the life of your fridge by allowing it to run more efficiently, which reduces your electric bill. Your fridge has at least two temperature controls (except on manual defrost types, which have one).
The one for the food compartment is a thermostat that turns the compressor on and off. The second, for the freezer, is just an air baffle. The baffle lets cold air from the freezer sink into the food compartment. Closing the baffle makes the freezer colder.
Set the temperature controls to the middle settings. Make any adjustments according to a refrigerator thermometer. The optimum setting for your fridge is between 38 and 42 degrees F; the freezer, between 0 and 10 degrees.
Drip openings allow water that has melted from the defrost cycle to flow down to a pan located by the compressor, where it evaporates. Check your owner’s manual for the location on your fridge. On cycle-defrost fridges, a channel directs the water to a tube in the food compartment.
On frost-free refrigerators, look for a small cap under the crisper drawers that covers a hole, or an opening in the back of the freezer or refrigerator. If the drain opening clogs, water will build up under the crisper drawers and eventually leak out onto the floor.
Find the drip opening on your fridge.
Locate the drip opening and wipe it out, being careful not to press any debris down into the hole. Suck out crumbs with a vacuum.
Service specialists will be the first to admit: A ton of their callers don’t require refrigerator repair service at all. The solutions are so easy they don’t even require a toolbox. Before you pick up the phone, check the following list. It just might save you money and a bit of embarrassment.